Find an experienced builder in Melbourne

Build a timber pergola (see photos of space and of reference pergola).

I have a garden shed that requires assembly and I can’t do it on my own.

Need someone to install a shed in our backyard. Shed details: - Brand: Stilla - Type: Cedar Shed Maple 12×6 - Size: 3.64 x 1.92 m https://www.stilla.com.au/product/maple-12x6/ Heavy duty timber floor will be supplied as part of the shed pack, so no need for concrete slab to be laid but it will need stumps set into the ground to support it. Stumps will be supplied but concrete will not. I expect the job will need to happen over a few days to allow the concrete to set for the stumps, before installing the shed on top. House has rear lane access to load in/out of. Ground around the shed will be cleared before the job. Shed due to arrive Thurs 13-June. Install date flexible but ideally as close to this as possible.

Asphalt driveway need to be repaired.

Need bathroom stripped out. This includes floor tiles, wall tiles, shower and bath. Plasterboard ceiling and walls to remain. Rubbish to remain on site no need for skip. Home is on ground level. Location Northcote

Repair a large pergola that has a wisteria growing over it

We need to repair the concrete driveway. The neighbouring tree has cause it to crack. There's an existing drain which may be salvageable.

Qualified chippy needed to build a pergola. Flat roof & will be fixed to a brick wall at the rear of a towhouse. Approx 2.9 x 4m Will pay day rate and i will pay for all materials. Must have own tools. On going work available. Est price is a minimum day rate

Put together an EasyShed. This is the shed details https://easyshed.com.au/products/narrow-slider-garden-shed-2-25m-w-x-0-78m-d-classic

Hi, I have a Parlam Feria 3 prefab flatpacked pergola which needs assembly and installation. It's a simple 3x3 lean to structure, the roof needs to be fixed along our timber garage wall section and the two adjustable legs need to be fixed down onto our brick yard. The installation guide says it requires 2 people and to allow half a day. More info in the links below. There are power points, a ladder etc. Please only quote if you have done similar handyman jobs on airtasker. Thanks! https://www.tiptopyards.com.au/product/pergola/feria-3-pergola-verandah-patio-cover/#assembly https://w6p3t6x2.rocketcdn.me/wordpress/wp-content/uploads/2018/05/82776_Palram-Canopia_Patio-Covers_Feria_3x3_10x10_Assembly-Instructions.pdf

Build a pergola at the back of restaurant,roughly 20 square meter Include materials

Need help assembling an EasyShed Bike Shed (Model: EBS-2308) Need a Power Drill, Phillips Head Driver, Pop Rivet Gun, Step ladder and Drill Bits (3mm Steel, 10mm Steel, 10mm Masonry). Want to fix it to a concrete slab in a car port. Have fixings required for that. Have the manual and item list as well as all materials still in the box.

Looking for a qualified Draftsman to build 2x two storey units on a subdivided corner block who is knowledgeable of the council procedures (preferably merri-bek council) happy to negotiate price

Looking at constructing a new build for a home in seaford area. Please message with contact details for plans etc

We have two active claims with insurance requiring the following to be provided by ABN registered builder Airtasker 1. detailed damage reports 2. quotes for insurance We need two of each of the mentioned above for the following claims: 1. Due to weather damage 2. Due to malicious damage/break in

10m approximately prefer wood Need retaining wall about 40cm high as part of fence Disposal also required

I am planning to convert my garage into a Small Office Unit (SOU) with a bedroom and bathroom, located in Saint Albans, Melbourne. I seek your expertise to ensure compliance with the National Construction Code (NCC) and to navigate the permit process efficiently. Below, I've outlined the specifics of my project with attention to compliance requirements: 1. **Insulation**: To meet the NCC's energy efficiency provisions, particularly Section J for residential buildings, I intend to incorporate high-performance insulation in walls and ceilings, ensuring an optimal thermal performance rating. 2. **Plumbing**: The addition of a bathroom necessitates compliance with NCC Volume Three - Plumbing Code of Australia (PCA), focusing on water efficiency, sanitary drainage, and waterproofing requirements. 3. **Waterproofing**: Adhering to AS 3740 - Waterproofing of domestic wet areas, to prevent moisture damage and ensure the integrity of bathroom areas. 4. **Ceiling Height**: In alignment with NCC Building Code of Australia Volume Two, Part 3.8.2, the conversion will feature ceiling heights of at least 2.4 meters for more than two-thirds of the floor area, providing adequate headroom and ventilation. 5. **Windows and Natural Light**: Upgrading garage windows to double-glazed units to enhance thermal efficiency and sound insulation, adhering to the NCC's Part 3.8.5 requirement for natural light. The design will ensure window sizes meet at least 10% of the floor area, aligning with NCC Volume Two, Part 3.8.4 for natural lighting. 6. **Garage Door**: Considering the installation of a new garage door with integrated windows, to fulfill the NCC's natural light requirements while contemplating aesthetics and functionality. The design will ensure compliance with relevant Australian Standards for garage doors in residential applications, considering security, insulation, and operational safety.

Need to build a partition wall with a door Location : Melbourne CBD Parking : Right infront of the building Unit : Apartment unit with easy lift access Wall size : approximately 5m with a door needed

Small stand-alone building measuring ±650m² with internal partitions to be physically measured up and both Pdf and cad plans to be drawn up accurately.

I have about 13 square meters of bathroom wall requiring cement board/blue board installed in a bathroom. - Due date: Before Friday, 15 December 2023